U-Boot > U-Boot > run sd.boot SW ECC selected NAND read: device 0 offset 0x200000, size 0x280000 2621440 bytes read: OK ## Booting kernel from Legacy Image at c2000000 ... Image Name: Linux-2.6.33-rc4 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2302088 Bytes = 2.2 MB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 2.6.33-rc4 (duyky@duyky-ubuntu) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #8 PREEMPT Tue May 1 21:21:37 PDT 2012 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DA850/OMAP-L138/AM18xx EVM Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 32768 free_area_init_node: node 0, pgdat c04a38b0, node_mem_map c04c7000 DMA zone: 256 pages used for memmap DMA zone: 0 pages reserved DMA zone: 32512 pages, LIFO batch:7 DaVinci da850/omap-l138/am18xx variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: root=/dev/mmcblk0p1 rw ttyS2,115200n8 rootwait PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 124912KB available (4360K code, 324K data, 164K init, 0K highmem) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 149.50 BogoMIPS (lpj=747520) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok DaVinci: 144 gpio irqs regulator: core version 0.5 NET: Registered protocol family 16 bio: create slab at 0 SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb regulator: VDCDC1: 3200 <--> 3300 mV at 3300 mV regulator: VDCDC2: 1750 <--> 3300 mV at 3300 mV regulator: VDCDC3: 950 <--> 1375 mV at 1200 mV regulator: LDO1: 1800 mV regulator: LDO2: 1150 <--> 1300 mV at 1200 mV i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL) vpif vpif: vpif probe success Switching to clocksource timer0_1 musb_hdrc: version 6.0, cppi4.1-dma, otg (peripheral+host), debug=0 Waiting for USB PHY clock good... musb_hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn) musb_hdrc: MHDRC RTL version 1.800 musb_hdrc: setup fifo_mode 2 musb_hdrc: 8/9 max ep, 3904/4096 memory musb_hdrc: USB OTG mode controller at fee00000 using DMA, IRQ 58 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: MII PHY configured, RMII PHY will not be functional JFFS2 version 2.2. (NAND) B) 2001-2006 Red Hat, Inc. msgmni has been set to 244 io scheduler noop registered (default) da8xx_lcdc da8xx_lcdc.0: GLCD: Found Sharp_LK043T1DG01 panel Console: switching to colour frame buffer device 60x34 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a 16550A serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a 16550A serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a 16550A console [ttyS2] enabled brd: module loaded loop: module loaded ahci ahci: version 3.0 ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci ata1: SATA max UDMA/133 irq 67 NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Bad block table not found for chip 0 Bad block table not found for chip 0 Scanning device for bad blocks Bad eraseblock 885 at 0x000006ea0000 Bad block table written to 0x000007fe0000, version 0x01 Bad block table written to 0x000007fc0000, version 0x01 Creating 5 MTD partitions on "davinci_nand.1": 0x000000000000-0x000000020000 : "u-boot env" 0x000000020000-0x000000040000 : "UBL" 0x000000040000-0x0000000c0000 : "u-boot" 0x000000200000-0x000000600000 : "kernel" 0x000000600000-0x000007fc0000 : "filesystem" davinci_nand davinci_nand.1: controller rev. 2.5 console [netcon0] enabled netconsole: network logging started ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 2 ohci ohci.0: irq 59, io mem 0x01e25000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 3e:c7:ee:d1:5e:f1 usb0: HOST MAC 32:4f:77:a5:72:c5 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected i2c /dev entries driver Linux video capture interface: v2.00 tvp514x 1-005d: tvp514x 1-005d decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp514x-0 tvp514x 1-005c: tvp514x 1-005c decoder driver registered !! vpif_capture vpif_capture: registered sub device tvp514x-1 vpif_capture vpif_capture: VPIF Capture driver initialized usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) watchdog watchdog: heartbeat 60 sec cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode Registered led device: led1 hub 3-0:1.0: activate --> -22 ata1: SATA link down (SStatus 0 SControl 300) Registered led device: led2 usbcore: registered new interface driver usbhid usbhid: USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.21. usbcore: registered new interface driver snd-usb-audio No device for DAI tlv320aic3x asoc: tlv320aic3x <-> davinci-i2s mapping ok ALSA device list: #0: DA850/OMAP-L138 EVM (tlv320aic3x) TCP cubic registered NET: Registered protocol family 17 Clocks: disable unused emac Clocks: disable unused spi1 regulator_init_complete: incomplete constraints, leaving LDO2 on regulator_init_complete: incomplete constraints, leaving LDO1 on regulator_init_complete: incomplete constraints, leaving VDCDC3 on regulator_init_complete: incomplete constraints, leaving VDCDC2 on regulator_init_complete: incomplete constraints, leaving VDCDC1 on //>> Random MAC addr : >> MAC_ADDR 00 00 00 00 00 00 emac-mii: probed //>> davinci_emac_probe : >> MAC_ADDR 00 12 34 56 78 91 omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) Waiting for root device /dev/mmcblk0p1... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SD card at address 0002 mmcblk0: mmc0:0002 00000 971 MiB mmcblk0: p1 EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem) on device 179:1. Freeing init memory: 164K << Start rcS for System Start-Up>> Assign HW MAC //>> emac_dev_setmac_addr : >> MAC_ADDR 00 12 34 56 78 92 Start udhcpc udhcpc (v1.19.4) started Sending discover... Sending select for 10.1.1.76... Lease of 10.1.1.76 obtained, lease time 86400 adding dns 10.1.1.1 Start ntpd to get / set time Start inetd Start httpd Start telnetd << Done rcS >> Please press Enter to activate this console. << Start Shell Profile >> Sat May 12 11:47:28 PST 2012 << Done profile >> arm_76:/home % date Sat May 12 11:47:30 PST 2012 arm_76:/home % arm_76:/home %